Brand new and original MTL5510 4 channel isolated barrier in stock with good price for sale.
MTL4510 – MTL5510 SWITCH/ PROXIMITY DETECTOR INTERFACE 4-channel, digital input
The MTLx510 enables four solid-state outputs in the safe area to be controlled by up to four switches or proximity detectors located in a hazardous area. Each pair of output transistors shares a common terminal and can switch +ve or –ve polarity signals. A range of module configurations is available (see Table 1) through the use of selector switches. When proximity detector modes are selected, LFD is enabled and the output switches to OFF if a line fault is detected.
SPECIFICATION
See also common specification
Number of channels
4, configured by switches
Location of switches
Zone 0, IIC, T6 hazardous area Div 1, Group A hazardous
location Location of proximity detectors
Zone 0, IIC, T4-6 hazardous area if suitably certified Div 1, Group A, hazardous location
Hazardous-area inputs
Inputs conforming to BS EN60947–5–6:2001 standards for proximity detectors (NAMUR)
Voltage applied to sensor 7 to 9V dc from 1kΩ ±10%
Input/output characteristics
Normal phase Outputs closed if input > 2.1mA (< 2kΩ in input circuit)
Outputs open if input < 1.2mA (> 10kΩ in input circuit)
Hysteresis: 200µA (650Ω) nominal
Line fault detection (LFD) (when selected)
User-selectable via switches on the side of the unit.
Open-circuit alarm on if Iin < 50µA
Open-circuit alarm off if Iin > 250µA
Short-circuit alarm on if Rin < 100Ω
Short-circuit alarm off if Rin > 360Ω
Note: Resistors must be fitted when using the LFD facility with a contact input
500Ω to 1kΩ in series with switch
20kΩ to 25kΩ in parallel with switch
Safe-area outputs
Floating solid-state outputs compatible with logic circuits
Operating frequency: dc to 500Hz
Max. off-state voltage: ± 35V
Max. off-state leakage current: ± 50µA
Max. on-state resistance: 25Ω
Max. on-state current: ± 50mA
LED indicators
Green: power indication
Yellow: four: on when output active
Red: LFD indication + faulty channel’s yellow LED flashes
Maximum current consumption
40mA at 24V (with all output channels energised)
Power dissipation within unit： 0.96W at 24V, with 10mA loads
Safety description (each channel) Uo=10.5V Io=14mA Po=37mW Um = 253V rms or dc
MTL5500 Series Barriers
Part Number
MTL5501-SR, MTL5510, MTL5510B, MTL5511, MTL5513, MTL5514, MTL5514D, MTL5516C, MTL5517, MTL5521, MTL5522, MTL5523, MTL5523V, MTL5523VL, MTL5524, MTL5525, MTL5526, MTL5531, MTL5532, MTL5533, MTL5541, MTL5541A, MTL5541AS, MTL5541S, MTL5544, MTL5544A, MTL5544AS, MTL5544D, MTL5544S, MTL5546, MTL5546Y, MTL5549, MTL5549Y, MTL5561, MTL5575, MTL5576-RTD, MTL5576-THC, MTL5581, MTL5582
MTL5500 series
Part NumberDescription
Digital Input
MTL5501-SR 1ch DI failsafe solid-state output + LFD alarm
MTL55104ch DI solid-state ouput
MTL5510B4ch DI multifunction solid-state output
MTL55111ch DI relay output
MTL5513 2ch DI solid-state output
MTL5514 1ch DI relay output + LFD alarm
MTL5514D 1ch switch/prox input, dual output relay
MTL5516C2ch DI with changeover relay output
MTL55172ch DI relay output + LFD alarm
Digital Output
MTL5521Loop powered solenoid driver, IIC
MTL5522 Loop powered solenoid driver, IIB
MTL5523Solenoid driver with LFD
MTL5523V - VL Solenoid/Alarm driver with voltage control
MTL5524 Switch operated solenoid driver
MTL5525Loop powered solenoid driver low power
MTL55262ch switch operated relay
Analogue Input
MTL55411ch 2/3 wire Transmitter repeater
MTL5541A 1ch Transmitter repeater, passive input
MTL5541AS1ch Transmitter repeater, passive input, current sink
MTL5541S1ch 2/3 wire Transmitter repeater, current sink
MTL5544 2ch 2/3 wire Transmitter repeater
MTL5544A 2ch Transmitter repeater, passive input
MTL5544AS 2ch Transmitter repeater, passive input, current sink
MTL5544D1ch 2/3 wire Transmitter repeater, dual output
MTL5544S2ch 2/3 wire Transmitter repeater, current sink
Analogue Output
MTL55461ch 4-20mA smart isolating driver + LFD
MTL5546Y 1ch 4-20mA smart isolating driver + oc LFD
MTL55492ch 4-20mA smart isolating driver + LFD
MTL5549Y2ch 4-20mA smart isolating driver + oc LFD
Temperature Input
MTL55751ch Temperature converter, RTD / THC with alarm
MTL5576-RTD2ch Temperature converter, RTD
MTL5576-THC2ch Temperature converter, THC
MTL55811ch mV/THC isolator for low-level signals
MTL55821ch resistance isolator
Pulse and Vibration
MTL5531 1ch vibration probe interface
MTL5532 1ch pulse isolator, digital or analogue output
MTL55332ch vibration probe interface
Fire and Smoke
MTL5561 2ch loop-powered, for fire and smoke detectors
General
MPA5500 85 - 265V ac power adaptor
MTL5599Dummy isolator
MTL599124V dc power supply
